Brady Windows Printer Drivers

5.1.00.4354

• Cutter functionality corrected for printing from Windows applications and cutter set to cut every n labels.

5.1.00.4326

• Fixed issue where Cancel before print could not be set back to "No".

5.1.00.4314

• Internal counter now works also when using stored layout on the printer. ("store & recall" or "export to printer" options in labeling software)

5.1.00.4306

• Solved problem with multi-thread printing (sometimes the stream is not correct).

5.0.05.4297

• Gap / Black mark length and offset size is now limited to 1 inch.

5.0.03.4192

• QR barcode is supported on DPL printers.Prefix and suffix enabled for counters.

5.0.03.4183

• Date offset is now supported on RTC for DPL printers. Offset is set in days.The limitation is one RTC variable with offset on the label.Offset does not work with time variable because of printer firmware limitation.

5.0.02.4116

• Fixed issue with labels after the first one having incorrect date/time data when using internal date/time.

5.0.02.4105

• Datamatrix barcode is no longer printed too small on 300 dpi models

5.0.00.4197

• Driver help for barcode font "y dimension" updated.

5.0.00.3976

• Added vertical graphic optimization to allow ribbon saver to work on color printers.

5.0.00.3897

• All the drivers are now digitaly signed to allow installation on Windows 8.

5.0.00

• Update solves problems when printing color images with transparent color from Windows applications (for instance PNG image with transparent color). We tested several Word applications, but the problem was observed only with Word 2007 (with all updates installed). The symptom is that images were converted in one color and that colors were not converted correctly (usually all colors were converted to one color - black).

4.6.78.3865

• ASCII characters under 32 needs special handling on CAB printers. Before this change printer goes into error state in case of using such characters for data (CR/LF is the most common). This is fixed now.

4.6.78.3840

• In some rare cases driver crashed when printing a Code128 barcode. This is corrected now.

4.6.76.3795

• Maximum expansion for QR barcode is greater then 10 which was previous limitation. It is set to 99 now for TSPL printers.

4.6.76.3790

• Fixed occasional Spooler crash when printing Word document with very long filename.

4.6.76.3782

• Advanced Port monitor can now be added by using Windows Add New Port Type option.

4.6.76.3772

• User can now manual encode the Code128 when doing export to printer or general export with ZPL models.For this feature also NL must be updated (build after July 10th 2012).

4.6.76.3766

• When doing Export to SAP from labeling software the line with variable definition should not be present, like it is when doing Export to printer.This is corrected now.

4.6.76.3764

• Empty graphics are no longer sent when "Force graphic optimization" switch is turned on.

4.6.76.3763

• Port monitor now reconnectes to printer after lost connection

4.6.76.3760

• Horizontal print offset for color printers is now available for both print heads

4.6.76

• Cancel before print commands are no longer sent if bi-direcitonal printing is disabled

4.6.75.3745

• Printer driver can cancel jobs that are currently printing before starting with new print job.

4.6.74.3733

• Added support for QR bar code

4.6.74.3714

• Numeric GS1Databar barcode types no longer have data size requirements

4.6.73.3699

• CAB printer supports now unlimited print quantity. Before this update 9999 was maximum quantity.

4.6.73.3690

• Maximum expansion for Code128 on ZPL printers is set to 20

4.6.73.3682

• New printers BSP61 62L, BSP61 62R, BSP61 34L and BSP61 34R were added to Brady printer driver distribution.

4.6.72.3647

• German translation for Tear Off Distance was Abrißabstand, which was wrong. We corrected this translation to Abrisskante.

4.6.71.3635

• Date and time fileds are supported in GS1 barcode on ZPL printers. New date formats were added.

4.6.69.3612

• Driver update didn't preserve settings for all installed printers. This is fixed now.

4.6.69.3581

• DPL Vector fonts (CG Times, CG Triumvirate) printed from other Windows applications and not from labeling software were positioned wrong. This is corrected now.

4.6.67.3555

• RTC is now supported inside EAN-128 barcode on EPL printers.

4.6.67.3533

• Operation mode now supports a new option called "Stream".

4.6.67.3524

• Barcode verification options were added to printer driver.

4.6.67.3516

• New image optimization option added to printer driver.

4.6.66.3658

• In some case of printing big graphics (color on 64-bit OS for example) the graphic elements could be missing. This is corrected now.

4.6.66.3436

• Obsolete monitor.inf files were removed from drivers that still had them

4.6.66.3392

• Removed warning message for special ports, when installing printer driver with Printer Installation Wizard.If connected to standard Windows TCP/IP port then show warning message.

4.6.66.3379

• Error message shows when doing Export to RedPrairie or General Export and on the label UPC or Postnet barcode was used.

4.6.65.3370

• Added safe graphic printing option as a solution to graphics printing over each other on TSPL printers.

4.6.65.3360

• Printer error detailes were missing while printing. The status reporting issue was limited to NicePrintQueue, Enterprise Print Manager(EPM) and NiceLabel.:p

4.6.64.3290

• Advanced TCP/IP port monitor now supports connections to names as well as IP addresses.

4.6.64.3284

• UPC-A is sent without check digit to the ZPL printer, because printer add the check digit by itself.UPC-E has been already work in this way. The reason is that old ZPL printers take the last 11 digits for data and not first 11 digit (of 12) for data.

4.6.64.3257

• Gap value maximum increased to maximum printer supported value (1 meter)

4.6.64.3252

• Pause printer command added in Batch printing actions

4.6.63.3224

• Rotation option on userinterface and QR and MicroQR barcode font rotation now work correctly

4.6.62.3204

• Cut offset 1 does not get disabled when "cut every" is selected

4.6.62.3190

• Spooler crash when changing printer port while printing was fixed.

4.6.62.3172

• Support for PDF417, QR, MaxiCode and Datamatrix barcode added.

4.6.62.3170

• If user sets the RFID transponder offset in the printer setup, this could cause a problem with the printer because the offset causes, that much of the label does not get printed whenever the elements is sent after the RFID command. Everything that is send before the RFID command, prints fine. Now we have change the print stream, that RFID command is always the last of all elements. In this case there is no problems with the print getting cut off.:p

4.6.62.3156

• Custom settings for unprintable now work correctly

4.6.62.3142

• When doing "Export to printer", user must enter variable values and print quantity at once!! But the label format should be just stored to the printer, and then when recalling the label the variable value and print quantity needs to be entered.
• When doing Export to Printer now user have to variants: Export to Printer and Export to File. Exporting to file needs the printer connected to port FILE and in this case the label file is different and could be used then on printer's memory slot CF or USB for recall format.

4.6.61.3091

• Cutting and perforation should now work correctly when using variable data in labels.

4.6.59.3036

• Printers with CAB programming language support now also internal counters on barcode elements.

4.6.59.3029

• New RTC formats for CAB printers:DD.MM.YYYY, DD.MM.YY, MM.DD.YYYY, MM.DD.YY

4.6.59.3002

• Printer ports are now properly shown in Options dialog.

4.6.59.3001

• Descender bars are always present on EAN and UPC barcodes.

4.6.59.2995

• Changed font for Chinese Windows to SimHei.

4.6.57.2946

• Graphic positioning to allow centering with stream optimization providing safe graphic printing is turned on

4.6.52.2832

• User is now able to select the option for internal RTC which allows printer to use the time read from RTC when the label is printed and not use the time of first label. The option could be found on "Advanced Setup > Other" dialog.

4.6.52.2829

• In old driver peel and dispense option didn't work if label present sensor check box wasn't checked. This is corrected now. If user selects peel or dispense, label present sensor check box is automatically checked.

4.6.52.2819

• When user export label format to printer, it is prompt now every time for quantity number. Before this change the format has been printed unlimited (9999) if you select the label format from memory card.

4.6.51.2800

• Czech, Lithuanian and Ukrainian languages are now supported also in all NiceDrivers.

4.6.51

• Wrong command is used for locking RFID tag.

4.6.50.2784

• Graphic positioning when using database for graphical data is now correct providing user turns on "safe graphics printing"

4.6.50.2773

• When printing from standard Windows application (like Microsoft Word) and using page rotation (Landscape and/or rotate 180), positions of graphic were shifted relative to internal elements.Shift size depends on page dimensions, shift direction depends on rotation.

4.6.50.2756

• Updated EPC RFID commands.

4.6.49.2747

• PrnInst utility was updated so that long INF file structure is supported.

4.6.49.2611

• When trying to preinstall drivers on Windows 7, user got an "Environment incorrect" error message. This is corrected now.

4.6.48.2718

• Cut on last element is available only if no sensor is selected.

4.6.48.2709

• If user selected batch cut (cut at the end) the printout was not OK. This has been corrected and it looks the command for cycle cutter did not work correctly: Because of that it has been removed.

4.6.48.2645

• Added Aztec and GS1 Datamatrix barcodes. GS1 Datamatrix barcode works from NiceLabel version greater than 5.2.2865. Please check also your printer's firmware version if support these barcodes.

4.6.48.2644

• Memory slots correction for P4T and RP4T. Only Flash RAM is available from now on.

4.6.47.2571

• Cancel before print option added to ZPL printers. Command cancels all format commands in the buffer. It also cancels any batches that are printing.

4.6.46.2538

• Brady MiniMark had no Advanced menu. This is corrected now.

4.6.46.2533

• Fixed issue with labels designed wider then maximum print width which could cause printer to print graphics incorrectly.

4.6.44.2503

• YOffset did not work OK when it was used continuous paper type. The label was cut and printed on wrong position (too soon).X and Y offset can not be negative.

4.6.44.2498

• Batch cut with variable data and/or true type counters now works correctly

4.6.44.2472

• Fixed problem with barcode Code39 when exporting to keyboard.

4.6.43.2464

• Negative offset values are now sent correctly for TSC printer models.

4.6.43.2445

• User is now able to change administrator settings without reopening driver properties dialog as an elevated user. A click on the shielded button and entering the credentials is all that is needed.

4.6.43

• There is one additional button (Run as administrator) on the printer's language dialog when current user has insufficient rights to change dialog's language.

4.6.42.2401

• Brady BBP72 printer added

4.6.41.2378

• Brady BP-PR 360 PLUS model added to distribution.

4.6.41.2364

• Fixed occasional driver crash when printing extremely large graphics

4.6.41.2363

• Switching to PCX download now works

4.6.41.2361

• Page preview icons in "Advanced Dialog" corrected.

4.6.41

• Correction on Advanced tab dialog for Chinese language.
• New export variants added to TSC driver.
• Printing internal clock improvement.
• Offsets sent in mm will not be sent as they were entered in driver interface
• FONT 0 added to TSC driver.

4.6.37.2305

• Partial Cut option was not stored on Advenced setup dialog. This is corrected now.

4.6.37.2258

• Uninstall of printer with Printer Install Wizard did not work on Windows 2003 (x64) system

4.6.34.2269

• Time format hh:mm:ss is not supported.

4.6.33.2236

• All 1D barcodes on EPL printer do not have limitation for maximum height set to 600dots anymore. Limitation is now set to 1200 dots.

4.6.30.2157

• Media Type selection enabled on printers without display and disabled on printers with display.

4.6.26

• Export to printer functionality is added for TSPL printers.

4.6.22

• Build number is now part of version information in About dialog

4.6.15

• Added options to turn off print optimization on printers using CAB printer language
• New Brady printer models are supported: BRADY BBP11-24LBRADY BBP11-34L

4.6.14

• DPL printers have ability to print inverse text. This option is supported now also in NiceDrivers.
• Macros 05 and 06 on Datamatrix are now supported on printer models with ZPL and DPL printer language.
• DPL printer will print unlimited labels quantity with quantity command of 9999.

4.6.13

• Added new date/time options when using printer clock on CAB printers.

4.6.11

• Corrected printing of SSCC-18 barcode with variable data

4.6.09

• French translation have been updated for CAB driver language and also for some general driver dialogs.

4.6.07

• When exporting Code128 to the printer and using variable, the ZPL code use optimization build in the printer's firmware for optimized Code128 encoding.

4.6.05

• Driver sends "(00)+Data" instead of just "00+Data" for SSCC barcode for correct encoding on ZPL printers.

4.6.04

• Printing internal Maxicode and PDF-417 now works.
• The internal date/time fields could only be used with the internal fonts Datamax1 and Datamax2. When you used any other internal font (including CG Times), the internal date/time didn't get printed. This is corrected now.
• WYSIWYG for internal fonts is corrected for DPL printers.
• Brady BP 1244 and BP 1344 models have darkness range extended from 0..20 to 0..30.

4.6.03

• EPL printers can use option "KDU Repeat Prompt" when exporting label format to printer memory and using recall with KDU keyboard. With this option enabled, user will have to enter variable value on KDU keyborard on every recall. Option can be found on Advanced setup > Miscellaneous dialog.

4.6.02

• PDF417 barcode height maximum limitation is 99 and not just 24.

4.6.01

• Postnet barcodes has wrong expansions and are printed too big. This is corrected now and WYSIWYG is OK.
• Added Rotation to parsed text in command fonts

4.6.00

• Printing process was stopped during heavy duty printing.
• Barcode height is corrected for non-203 dpi printers.

4.5.42

• Driver print speed optimization

4.5.40

• Database fed empty elements from Labeling software are now printed correctly
• Offsets on CAB printers for perforation before/after label and cutting before label now allow negative values (-9.9mm - 9.9mm)

4.5.39

• PrnInst showed login window, even if the user running the application was administrator.

4.5.38

• New model added to distribution: Brady BBP81
• TSPL printers now support also SHIFT command which can be used to fine-tune the entire label up or down from its current position.

4.5.37

• PrnInst can now be moved to any position (second monitor) and it will stay there. It will not jump back to its original position.

4.5.34

• Postnet barcode fonts can no longer have their width changed.

4.5.33

• Following models added to Brady distribution: BP-THT Precision 200, BP-THT Precision 300, BP-THT Precision 600, BP-PR 200 PLUS, BP-PR 300 PLUS, BP-PR 600 PLUS, PAM 3630, PAM 3660, MiniMark, BP-THT IP 300 and BP-THT IP 600.

4.5.32

• Graphic symbol font (GS) is supported now on ZPL printers. User can print Registered Trade Mark, CopyRight, Trade Mark, Underwriters Laboratories approval and Canadian Standards Association approval symbols with typing A,B,C,D or E for internal text.

4.5.30

• EPL printers sent cut offset in all cases (c commands). This is corrected now.

4.5.14

• Fixed issue with forced optimization in non labeling software.
• Fixed issue with barcode fonts causing protocol error
• Added explanation for "Forced optimized printing" option
• User can use RTC offset from labeling software but the driver will send just offset in minutes for TIME format and days offset for DATE format. Hour/second/month/year offsets are ignored from the GUI.

4.5.13

• Internal elements now get filtered out when not using labeling software and forcing optimization
• Fixed issue with printing from word using forced optimization
• Datamatrix barcode can get negative coordinate in print stream, and also the size and WYSIWYG is not ok. This is corrected now.

4.5.12

• Partial cut option is enabled on some TSPL models. With this option the label won't back feed when it is cut off.
• User can select Automatic or Manual options for Job removing using keyboard in Printer Install Wizard
• Fixed labeling software crash when turning off "Use Advanced printer driver interface".
• There was wrong command sequance present in print stream when setting tear off/peel off/ cutter option. This is corrected now.There was added also cutter functionality of "Partial" cutter into some TSPL models.

4.5.11

• Fixed command sequence for export to printer
• Printer Install Wizard uninstallation of driver doesn`t remove all of the files from the SYSTEM32\spool\drivers\w32x86\3\ folder.

4.5.10

• UCC/EAN128 barcode now produces correct command on EPL printers.
• Also barcodes now uses "SO2" command for first date/time offset and "SO32 command for the second and all further date/time offsets on the same label.

4.5.09

• Barcodes in labeling software with prompted contents are not exported correctly to the printer.
• Electonic Article Survailance was always disabled on Rfid printers
• Fixed printing of Datamatrix and QR barcode font with more then 255 character data
• Added automatic termination character for Maxicode barcode font data

4.5.07

• Added support for custom printer name after silently installing a printer driver from command line (/INSTPRN; /INSTMULTPRN)

4.5.06

• Printer Installation Wizard will be able to automaticly remove all jobs when updating printer

4.5.05

• Printer Install Wizard can start an application specified in the command line, after it closes.

4.5.04

• ZPL printers now use absolute darkness escape (~SD) instead of relative (^MD).
• Fixed Advanced TCP/IP port to handle leading 0 in IP.

4.5.03

• When you disable the option "Use advanced printer driver interface" (in File -> Label Setup -> Printing tab) labeling software will crash with the error "GDI Failure, OK to continue?"
• Status monitor is able to detect port conflicts, when two printer drivers are using the same port for bidirectional communication with the printer.Also when user will delete or install a new printer to the system, Status Monitor will detect the change by itself.

4.5.02

• PrnInst didn't set printer attributes correctly. This is fixed now.

4.5.01

• Turkish language added
• Moved perforation commands in stream to avoid protocol errors

4.5.00

• New setting Printer default. If set, then printer will not send some settings from Options and Advanced Setup tab. This feature is useful for printers with LCD display where user would like to set printer parameters (speed, darkness...) manually.
• Added possibility of optimized printing of graphics from all windows software
• ^ character can now be encoded in Code128
• FNC1 is not encoded correctly in Datamatrix barcode.
• Fixed printer error when printing different pages from windows software
• - write MMF to alternative location (research) - update MemMaster to store files to this location - update driver to read from new location (make sure that the update will be backward compatible)

4.4.73

• Uninstall of driver package failed when running a 64bti system.

4.4.71

• Driver now sends driver settings only at the start of the print

4.4.69

• Labelling software can now recall variables with more than 31 characters of data.
• When you click on the Help button in About dialog help is opened, but it is not linked to any page.
• Help on About dialog opens help page with contents 'This program cannot display the webpage'.
• Internal elements with Date/Time offsets in labelling application now print correctly. The problems occured on ZPL printers (applicators).
• Checkbox "Enable bidirectional support" (Printer properties -> Ports) can now be unchecked automatically during driver installation, corresponding to the flag "Bidirectional" in .inf file.Bidirectional=0 => checkbox is unchecked.Bidirectional=1 => checkbox is checked.If this information is ommited, Bidirectional=1 is assumed.

4.4.68

• Optimized driver printing

4.4.67

• Implementation of Rfid Read and store for ZPL printers
• Fixed IMG compression for wide graphics

4.4.66

• There is possible in ZPL to print counter without leading zeros. This can be done with NL communication because this setting should driver get from NL.
• Now user don't need to create a start value of "001" to count from 1..999 on ZPL printers with printer's internal counter, but can set just "1" and counter will not stay at just one digit like before. But user have to set in this case tha maximum length of counter to 3 ! In this case leading zero's will not be printed, so if you want leading zero's you still have to imput 001 for example.WYSIWYG for non-leading zero's counters is not accurate because the printer gets the maximum counter length data and this can not be improved.

4.4.65

• Export label to printer works now correctly also for prompted variables,
• EPL printers support now also day offset for internal printer clock.It is possible to use internal date & time also on barcode element from now on.

4.4.64

• Removed Help button as no help is available.
• Export to printer didn't work properly. There was a wrong slot number in the exported print stream.
• New Japanese translation for Printer Install Wizard

4.4.63

• Downloaded fonts allways print in the same size, even if you resize them.
• DL of graphics on LPT port doesnt work correctly, when printing you get an empty screen
• When user starts Printer Install Wizard the application is shown but without focus
• Changed default number for cutting to 1 label instead of 0.

4.4.62

• Added new cutter commands to support new PCU4 cutter unit.
• Added new options to some printers: ingnore label position, ignore paper end, top side same as bottom, single buffer mode, top to bottom offset
• Command "c" (immediate cut) is not recomended and therefore it is disabled.
• Corrected Print mode setting command for export

4.4.61

• Rfid Read and Print is not working correct. When printing a barcode with values stored in the rfid tag, only a couple of "?" characters are printed.

4.4.60

• Changed file info for Printer Install Wizard
• Default value for Always use default settings is not correct when instaling it the driver with a configuration file attached.

4.4.55

• Incorrect stream is sent to printer when encoding Rfid Gen2 tags

4.4.53

• Read and Store functionality is not enabled on Rfid printers

4.4.52

• DLL files for user interface translation did not include version info data.
• Labels transfered from different systems now retain their driver settings.

4.4.51

• Increased lenght for filename and path in import and export of settings.
• POSTNET barcodes have a fixed height and width, but the interface allows the user to change these dimensions.

4.4.50

• Import and export didn't work if filename and path exceeded the length of 80 characters while windows support 256 character lengths
• Click on "Stocks" panel caused error if stock list was empty. This is fixed now.

4.4.30

• - support for preinstall on all supported platforms

4.4.01

• EndDocument escape was sent even when there was no StartDocument.
• "Tear Off" adjustment edit field is enabled all the time, no matter which operation mode is used. Before it has been enabled just when "Tear Off" operation mode was used.
• If driver gets no separator character description for decimal number from the OS, driver puts a "+" or "," string as default character. The result was seen for page size (example)Now the dot character "." is set for default separator in this case.

4.4.00

• Invalid stocks are now marked. User can open the Stock properties dialog and press OK to fix the problem (which is usually stock dimension). Stock size will be automatically adjusted.
• UI for commands fonts works now properly also in Japanese language.
• On Argox PPLB printers FNC characters, present in barcode data for Code128 are ignorred now. There is unknown command how to encode this characters into Code128.
• In some rare cases streams sent to the printer had an extra "0" added in it.

4.3.73

• Recall added for Zebra printers.
• Using 'Export to Printer' option in Labelling software creates wrong contents for maxicode barcodes. This only happens if barcode has variable contents.

4.3.72

• Implementation of Rfid Read and store for ZPL printers
• Added full Gen2 support for ZPL printers
• Sometimes a print stream is not send to the printer, and it stays stuck in the spooler

4.3.71

• Media type selection (Properties>Advanced setup>Other) has been added some time ago for all Datamax printers. But we have found some problems with this option for some printer models with display on printer's control panel. The problem is that printer resets itself when gets the command "KcXXX", so this option has been disabled for I-Class and W-Class printers.

4.3.70

• Media type selection (direct thermal, thermal transfer) is added into Datamax advanced setup dialog. User will find this option in secondary dialog which can be opened by button "Other".
• ^MMC command has been sent twice when exporting the label to the prrinter. This is corrected now and it is sent to the printer just once. ^MMC is a command for using cutter. If you select for "Operation Mode" Tear off the "^MMT" is sent and for Peel off "^MMP" command is sent.

4.3.63

• Added data format accepted values for ZPL printers. Accepted values can be in ASCII or HEX format.
• Port monitor crashed when setting up port details (IP and port number)

4.3.60

• Barcode fonts vanished instead of being imported.

4.3.59

• Microsoft Vista operating system is not mentioned in the text file that is distributed with the driver.
• Stocks were not imported if user didn't view the stocks dialog beforehand

4.3.56

• Advanced cutter option not working on some printers
• Applicator didn't work on PPLZ printers. This is corrected now.
• Barcode ratio values are not shown in Barcode Fonts dialog. This only happens when you are editing existing barcode font.

4.3.55

• Cut position control is always available now, but the command is sent just when the cutter is used. With this control user can change the cut position for max. +/-30 dots.
• Spooler crashed during the installation, if there were any printers allready installed on the system.

4.3.54

• Corrected speed settings for following models: TLP2844, LP2844, TLP2824, LP2824. Additional JJJ date mask was added for printers that support Julian Date.
• While installing a printer driver on certain systems the spooler crashed.
• "delete" button was enabled even if the barcode/command fonts list was empty. This is fixed now.
• Export of barcode fonts didn't work properly unless user clicked on barcode fonts tab before exporting them. This is fixed now.
• Graphics are in some cases larger then they need to be making label size incorrect.
• Increased timeouts for better printer status response times
• Barcodes with '"' character on EPL printers are not printed.
• Slow printing occurred when a Not Accessible printer was found on a network. Printer status was also not received immediately.

4.3.53

• Status for printers (that use bidirectionaal communication) was not correct when the printer was not physicaly connected to the computer. Status was changing between Not Accessible and Ready

4.3.51

• Driver can now override the default document settings of some applications with driver default settings (set up in printer spooler)

4.3.07

• After viewing the Help file CHM file was locked and because of that reboot was needed to complete the installation. New version of driver will not lock the CHM any more and because of that reboot is not needed.

4.3.06

• Barcode fonts and command fonts are now stored in registry.
• Printing did not work on nonbidirectional printers. Printer Error was displayed the whole time

4.3.05

• Printing did not work when bidirectional was enabled

4.3.04

• New Port monitor is added to the distribution
• On Windows Vista there is warning displayed if user doesn't have appropriate permissions to create (or write to) certain driver files.
• Old HLP help file format was exchanged for new CHM file format.
• When user changed printer's port, the printing was no longer possible until reboot.
• Port monitor now uses correct (64 bit) interface file on 64bit systems.
• Installation did not go through when upgrading from old printer driver, if the user had the driver connected to the Advanced Port Monitor (LAN)
• Bug fixed, where some changes on stocks updated default umprintable area values.
• Drivers with Unicode fonts do not show internal fonts on Windows Vista.

4.3.03

• Spooler crashed, if user had multiple bidirectional printers using the same port, while using a status monitoring application

4.3.02

• Stocks were not imported properly or were not shown immediately after import.

4.3.01

• Korean language added.
• Driver does not show all stocks in 'Stocks' combo box on 'Options' dialog. Missing stocks have heights that are near the maximum printer's limit.

4.3.00

• Changed window handling so that port monitor setup windows can appear on Vista
• Codabar barcode for ZPL printers should have ratios 1:3, 1:2 and 2:5 enabled.